Page 1 of 2
New Ruger 10/22 in stainless
Posted: Tue May 22, 2012 10:17 pm
by angelsfanbp
I just picked up a Ruger 10/22 in stainless. What are the "must have" accessories for these? I'm seeing a lot of aftermarket stuff for these.....any must have internals? I will post pics tomorrow.
Re: New Ruger 10/22 in stainless
Posted: Wed May 23, 2012 3:19 am
by pacanis
I've got the 10/22 carbine. The only must have that I needed was a sight I could see. I put a Williams peep and front sight on it. The bead is a little large for target shooting past 50 yds, but it works just fine for plinking closer. I've got a 25 rnd mag for it, too. Fun, reliable little gun.
Re: New Ruger 10/22 in stainless
Posted: Wed May 23, 2012 3:51 am
by Junk Yard Dog
I bought a blued model about 20 years back, all I did to it was mount a scope and pick up an extended magazine that I never use.
Re: New Ruger 10/22 in stainless
Posted: Wed May 23, 2012 4:47 pm
by angelsfanbp
Re: New Ruger 10/22 in stainless
Posted: Wed May 23, 2012 4:48 pm
by Junk Yard Dog
Re: New Ruger 10/22 in stainless
Posted: Wed May 23, 2012 6:56 pm
by Celt
22lr shopping spree! Nice!
Re: New Ruger 10/22 in stainless
Posted: Wed May 23, 2012 10:08 pm
by etprescottazusa91
Stainless, that's a really nice 10/22. The factory ten rounders are the most durable and reliable mags, keeps the profile of the rifle down also. Really nice 10/22 posted
Re: New Ruger 10/22 in stainless
Posted: Thu May 24, 2012 5:19 am
by Junk Yard Dog
Is the aluminium receiver stainless plated? If so have a care about putting any scratches or nicks in it. I had a Mossberg 590 with a stainless plated receiver, every tiny scratch caused the chrome to bubble around it.
Re: New Ruger 10/22 in stainless
Posted: Thu May 24, 2012 5:27 am
by Rongo
Perfect choice in a .22 rifle... One of the best overall on the market IMHO. I have 2... One is all original & the other has an over/under scope setup. Scope rings are elevated so I can still use the open sights... Great setup.
etprescottazusa91 wrote:Stainless, that's a really nice 10/22. The factory ten rounders are the most durable and reliable mags, keeps the profile of the rifle down also. Really nice 10/22 posted
True... But Ruger now makes a 25 round banana mag that is just as reliable. Not bad in price either. The factory trigger is a weak point on the 10/22... Very gritty & stiff. A new one would be a good consideration & since yours is new it already has the extended mag release. If your satisfied with the trigger your pretty much good to go.

Re: New Ruger 10/22 in stainless
Posted: Thu May 24, 2012 5:35 am
by ponycarman
Nice looking rifle! 22's are so much fun and cheap on ammo
Sent from my LS670 using Tapatalk
Re: New Ruger 10/22 in stainless
Posted: Thu May 24, 2012 12:42 pm
by desdem12
Re: New Ruger 10/22 in stainless
Posted: Sun May 27, 2012 8:10 pm
by bunkysdad
The receivers are painted, and the barrel is a bead blasted matt finish stainless steel. Do you have the fiber optic sights? If so all you may need is a trainload of ammo. Mine shoots the Winchester 333 and 555 just fine. They are the same ammo, just the number of rounds in the carton. Actually mine shoots everything just fine, including CCI Stingers. Did you know that the Stingers have a slightly longer case than a 22lr? About 1/8" longer I think to accomodate more powder. You might not notice because they have a slightly smaller weight bullet so the overall length is about the same.
Re: New Ruger 10/22 in stainless
Posted: Thu May 31, 2012 11:25 am
by Ironnewt
I have a extended mag release and sear kit on mine. (as well as a replacement barrel and stock) Check out RIMFIRE.COM for a lot of great ideas
Re: New Ruger 10/22 in stainless
Posted: Thu Jun 14, 2012 7:28 pm
by newmosinfan
Have the BX-25 mag. did the bolt release mod myself and have a center point red/green dot sight fun plinker
Re: New Ruger 10/22 in stainless
Posted: Wed Jun 27, 2012 10:00 am
by bunkysdad
The BX-25 is a real nice mag. Ruger sure took their sweet time producing them.
Re: New Ruger 10/22 in stainless
Posted: Wed Jun 27, 2012 2:50 pm
by BuckeyeSgt
Sweet looking .22 What is a good trigger? I really don't feel like spending $200 to upgrade the trigger.
Re: New Ruger 10/22 in stainless
Posted: Wed Jun 27, 2012 3:27 pm
by Longcolt44
I bought a trigger kit off gunbroker and did it myself, under 20 bucks. It isn't just an easy job to do and if I was to do it again I would take it to a gunsmith to install. I also changed the sights to Tech Sights, 70 bucks. I love them.
Re: New Ruger 10/22 in stainless
Posted: Sat Oct 06, 2012 12:27 pm
by Detour Rd.
Rongo wrote:Perfect choice in a .22 rifle... One of the best overall on the market IMHO. I have 2... One is all original & the other has an over/under scope setup. Scope rings are elevated so I can still use the open sights... Great setup.
etprescottazusa91 wrote:Stainless, that's a really nice 10/22. The factory ten rounders are the most durable and reliable mags, keeps the profile of the rifle down also. Really nice 10/22 posted
True... But Ruger now makes a 25 round banana mag that is just as reliable. Not bad in price either. The factory trigger is a weak point on the 10/22... Very gritty & stiff. A new one would be a good consideration & since yours is new it already has the extended mag release. If your satisfied with the trigger your pretty much good to go.

order the Timney Trigger for it. Drops right in.
Re: New Ruger 10/22 in stainless
Posted: Sat Oct 06, 2012 1:31 pm
by Buckhead
Every one should have at least one in there safe.

the one in the middle I love mine and I take it to the range most every time

Re: New Ruger 10/22 in stainless
Posted: Sat Oct 06, 2012 3:23 pm
by Detour Rd.
hell, its a great little rifle. Even girls can shoot it
